70 lines
2.1 KiB
Plaintext
70 lines
2.1 KiB
Plaintext
;===========================;
|
|
; List of supported G-codes ;
|
|
;===========================;
|
|
; G0: linear Move
|
|
; G4: Dwell
|
|
; G28: Move to Origin (Home)
|
|
; G90: Set to Absolute Positioning
|
|
; G91: Set to Relative Positioning
|
|
; G92: Set Position, only support A axis reset.
|
|
; M0: Stop or Unconditional stop
|
|
; M1: Sleep or Conditional stop
|
|
; M2: Program End
|
|
; M25: Pause SD print
|
|
; M42: Switch I/O pin
|
|
; M73: Set build percentage
|
|
; M80: ATX Power On
|
|
; M81: ATX Power Off
|
|
; M82: Set extruder to absolute mode
|
|
; M83: Set extruder to relative mode
|
|
; M92: Set axis_steps_per_unit
|
|
; M104: Set Extruder Temperature
|
|
; M109: Set Extruder Temperature and Wait, Example M109 S215
|
|
; M140: Set Bed Temperature (Fast)
|
|
; M141: Set Chamber Temperature (Fast)
|
|
; M190: Wait for bed temperature to reach target temp
|
|
; M191: Wait for chamber temperature to reach target temp
|
|
; M204: Set default acceleration
|
|
; M206: Offset axes
|
|
|
|
;==========================;
|
|
; List of relevant G-codes ;
|
|
;==========================;
|
|
; M92: Set axis_steps_per_unit
|
|
; e.g. M92 X87.489 Y87.489 Z87.489 E420:420
|
|
; M204: Set default acceleration
|
|
; M206: Offset axes
|
|
;
|
|
; G90: Set to Absolute Positioning (default)
|
|
; G91: Set to Relative Positioning
|
|
; G92: Set Position, "only support A axis reset." - in other machines, this can set new absolute origin
|
|
; M82: Set extruder to absolute mode (default)
|
|
; M83: Set extruder to relative mode
|
|
;
|
|
; M190: Wait for bed temperature to reach target temp
|
|
; M109: Set Extruder Temperature and Wait, Example M109 S215
|
|
;
|
|
; G0: linear Move - this is rapid linear move on other systems, G1 is normal speed linear move for them
|
|
; e.g. G0 X000 Y000 Z000 E000 F000
|
|
; F is feed rate, E is extruder
|
|
; Traditionally, S is used for "power", which may be laser power or spindle speed. N/A here.
|
|
; G4: Dwell (ms)
|
|
; e.g. G4 P1000
|
|
; G28: Move to Origin (Home)
|
|
; e.g. G28
|
|
; e.g. G28 X Y
|
|
;
|
|
; M0: Stop or Unconditional stop
|
|
; M1: Sleep or Conditional stop
|
|
; M2: Program End
|
|
; M73: Set build percentage
|
|
; e.g. M73 P100
|
|
;
|
|
; M80: ATX Power On
|
|
; M81: ATX Power Off
|
|
;
|
|
;
|
|
; M140: Set Bed Temperature (Fast) - does not wait!
|
|
; e.g. M140 S65 R40 (set to 65°C, wait until 40°C)
|
|
; M104: Set Extruder Temperature
|